Toggles

Toggle Wings 3/8"

22450525 Available: 28
Use for hollow wall
Use for concrete block

Mushroom Toggle Bolt 1/8"x3"

22450535 Available: 123
These toggle bolts are anchors for use in hollow walls and hollow masonry applications. The toggle bolt's wing spreads the force over a larger load bearing surface and comes attached to a machine screw. Toggle bolts are single-use anchors and should be properly positioned prior to pre-drilling the hole. 4 pieces per pack
Steel construction
Zinc-plated
1/8 in. x 3 in.

Toggler Plastic Toggle 50275 1/8"-1/4" 5pk

22450670 Available: 28
The TOGGLER Toggle TA hollow-door anchor provides a firm hold in 1/8"- to 1/4"-thick hollow-core doors and thin panels, includes #8 x 1-1/4" screws, and is made in USA. The anchor is made from polypropylene that resists corrosion, is nonconductive for anchoring electrical components, and is low-friction to facilitate screw installation. The anchor hammers into a 5/16" drilled hole until flush with the mounting material's surface. Before the screw can be inserted into the anchor to create a secure hold, the included key is used to open the anchor's wings behind the material. The fins on the anchor head grip the mounting material to prevent spinning when a screw is inserted, and the anchor will stay in place if the fastener is removed, facilitating fixture and screw changes. If using screws other than those supplied, the anchor accepts #8 to #12 size screws with a minimum thread length of 1". The Toggle TA anchor meets Federal Specification FF-B-588-D for Type IV anchors.
$3.99

Toggler Plastic Toggle 50300 3/8"-1/2" 5pk

22450675 Available: 38
Holds up to 143 lbs in 1/2 In. drywall with #8x1-1/2 In. combo head screw included in the package (Industry standards recommend 1/4 of this ultimate load per anchor)
Locks on walls and ceilings 3/8" to 1/2" for vibration-proof holding Packaged with #8x1-1/2" screw, but works with any screw #6 through #14 with minimum thread length 1-1/4" plus thickness of the item to be anchored
Can use a screw gun to install . anti-rotation fins prevent the anchor from spinning
$3.99

Toggler Plastic Toggle 50325 5/8"-3/4" 5pk

22450680 Available: 31
The Toggle TC commercial drywall anchor provides a firm hold in 5/8"- to 3/4"-thick drywall, includes #8 x 1-3/4" screws, and is made in USA. The anchor is made from polypropylene that resists corrosion, is nonconductive for anchoring electrical components, and is low-friction to facilitate screw installation. The anchor hammers into a 5/16" drilled hole until flush with the mounting material's surface. Before the screw can be inserted into the anchor to create a secure hold, the included key is used to open the anchor's wings behind the material. The fins on the anchor head grip the mounting material to prevent spinning when a screw is inserted, and the anchor will stay in place if the fastener is removed, facilitating fixture and screw changes. If using screws other than those supplied, the anchor accepts #6 to #14 size screws with a minimum thread length of 1-1/2". The Toggle TC anchor meets Federal Specification FF-B-588-D for Type IV anchors.
$3.99

Snap Toggler Anchor w/Bolts 3/16"

22450720 Available: 97
Toggle anchor installs behind 3/8"- to 3-5/8"-thick hollow materials including gypsum board, drywall, and concrete block to provide a secure hold from within the mounting material
Anchor affixes to the wall before adding the bolt and fixture, allowing one-person installation and fixture changes
Made in USA, and includes 3/16"-24 UNC-threaded bolts
Ultimate tensile strength is 238 lb. in 1/2" drywall and 802 lb. in concrete block with a 3/16"-24 UNC bolt
Use one-fourth or less of listed maximum values for safe working loads (as required by local regulations)
$3.99

Toggler Snap Toggle 50400 1/4"

22450725 Available: 66
Hollow-wall heavy anchors. They work in a snap. The straps snap off flush with the wall. The metal channel pushes aside insulation.
$3.99